Olympus Microcassette Recorder VN 7600PC User Manual

DIGITAL VOICE RECORDER  
VN-7600PC  
EN  
INSTRUCTIONS  
Thank you for purchasing an Olympus Digital Voice Recorder.  
Please read these instructions for information  
about using the product correctly and safely.  
Keep the instructions handy for future reference.  
To ensure successful recordings, we recommend that  
you test the record function and volume before use.  
Shinjuku Monolith, 3-1 Nishi-Shinjuku 2-chome, Shinjyuku-ku, Tokyo 163-0914, Japan. Tel. +81 (0)3-3340-2111  
3500 Corporate Parkway, P.O. Box 610, Center Valley, PA 18034-0610, U.S.A. Tel. 1-888-553-4448  
For customers in North and South America:  
Declaration of Conformity  
Model Number:  
Trade Name:  
VN-7600PC  
DIGITAL VOICE RECORDER  
Responsible Party: OLYMPUS IMAGING AMERICA INC.  
Address:  
3500 Corporate Parkway, P.O. Box 610, Center Valley,  
PA 18034-0610,U.S.A.  
Telephone Number: 1-888-553-4448  
This device Complies with Part 15 of the FCC Rules. Operation is subject to the following  
two conditions: (1) This device may not cause harmful interference, and (2) this device  
must accept any interference received, including interference that may cause undesired  
operation.  
Tested To Comply  
With FCC Standards  
FOR HOME OR OFFICE USE  
Canadian RFI:  
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital  
apparatus as set out in the Radio Interference Regulations of the Canadian Department of  
Communications.  
Cet appareil numérique ne dépasse pas les limites de la Catégorie B pour les émissions de bruit  
radio émanant d’appareils numériques, tel que prévu dans les Règlements sur l’Interférence  
Radio du Département Canadien des Communications.  
Introduction  
The contents of this document may be changed in the future without advanced  
notice. Contact our Customer Support Center for the latest information relating to  
product names and model numbers.  
The utmost care has been taken to ensure the integrity of the contents of this  
document. In the unlikely event that a questionable item, error, or omission is  
found, please contact our Customer Support Center.  
Any liability for passive damages or damage of any kind occurred due to data loss  
incurred by a defect of the product, repair performed by the third party other  
than Olympus or an Olympus authorized service station, or any other reason is  
excluded.  
Trademarks and registered trademarks:  
Microsoft, Windows and Windows Media are registered  
trademarks of Microsoft Corporation.  
Macintosh is the trademark of Apple Inc.  
Other product and brand names mentioned herein may be  
the trademarks or registered trademarks of their respective  
owners.  
hSafe and Proper Usage  
Before using your new recorder, read this manual carefully to ensure that you know how to operate  
it safely and correctly. Keep this manual in an easily accessible location for future reference.  
The warning symbols indicate important safety related information. To protect yourself and others from  
personal injury or damage to property, it is essential that you always read the warnings and information  
provided.  
U1-BS0485-01  
 AP0912  
1
- -  
Replacing the Batteries:  
When [N] appears on the display, replace the batteries as soon as possible. Size-AAA alkaline  
batteries are recommended. When the batteries are depleted, [O] appears on the display, and  
the recor-der shuts off.  
To replace the battery, make sure that you set the HOLD switch to the opposite direction of the  
arrow before replacing.  
hPower Supply  
Poweron:SlidetheHOLDswitch in the direction  
opposite that indicated by the arrow.  
Power off: Slide the HOLD switch in the  
direction indicated by the arrow while the  
recorder is not in operation.  
Standby Mode and Display Shut Off:  
If the recorder is stopped for 5 minutes or longer during  
recording or playing, it goes into Standby (power-save)  
mode, and the display shuts off. To exit Standby mode  
and turn on the display, press any button.  
hHold  
Setting the HOLD switch to the direction of the arrow holds the current status, and all button  
operations are disabled. Remember to release the HOLD switch to use the recorder.  
hSetting Time and Date [Time & Date  
]
If you have set the time and date, information as to when a sound file was recorded is stored  
automatically with that file.  
When you install batteries for the first time or each time you replace the batteries, the  
“Month” indication will flash. In such a case, be sure to set the time and date by following  
steps 4 through 6 described below.  
1 Press and hold the DISP/MENU button for 1  
second or longer to go to the main menu.  
2 Press the 9 or 0  
button to select  
[
Sub Menu].  
3 Press the PLAY  
/OK (`)  
Time & Date  
button.  
[Time & Date] appears on the  
display, and [ ] flashes.  
\^]  
4 Press the 9 or 0  
button to select the item  
to set.  
Select the item from “Month”,  
Day”, Year”, “Hour” and  
Minute” with a flashing  
point.  
1. 1‘08 12:00AM  
5 Press the  
+or – button to  
set.  
Follow the same steps by press-  
ing the 9 or 0 button to  
elect the next item, and press  
the + or – button to set.  
1. 1‘08 12:00AM  
7.25‘08 3:00PM  
6 Press the PLAY/OK (`)  
button to complete the  
setup screen.  
The clock will start from the set  
date and time.  
Press the PLAY/OK ( `) button  
according to the time signal.  
7 Press the STOP (4) button to close the menu  
mode.  
This completes the time and date setup procedure.  
Notes:  
You can choose between 12 and 24 hour display by pressing the DISP/MENU button while setting  
the hour and minute.  
You can change the order of the date indication by pressing the DISP/MENU button while you  
are setting the year, month, or day.  
 
3
- -  
Recording  
Current folder  
hNotes on the Folders  
The recorder provides five folders, [F], [G], [H], [I] and [W]. To  
change the folder selection, press the FOLDER/INDEX button while  
the recorder is stopped.  
Note:  
15m15s  
14m15s  
14m15s  
Up to a total of 200 files can be recorded in each folder.  
hRecording  
a
1 Press the FOLDER  
/
INDEX button to select  
the desired folder.  
a Current folder  
15m15s  
15m15s  
2 Press the REC (s) but-  
ton to start recording.  
The record/play indicator light  
turns red, and recording starts.  
If you start recording after in-  
serting the earphone into the  
earphone jack on the recorder,  
you can hear the sound being  
recorded. The sound volume  
on the recording monitor can  
be adjusted by pressing the +  
or – button.  
14m15s  
b c  
d
b Current recording mode  
c Current file number  
d Recording time  
e Remaining recording time  
f Recording level meter  
Remain 22h52m46s  
e
f
3 Press the STOP (4) button to stop record-  
ing.  
New recordings are saved as the last file in the folder.  
hTo Pause Recording  
To Pause:  
While the recorder is during  
recording mode, press the REC  
(s) button.  
[Rec Pause] appears on the display.  
Rec Pause  
To Resume Recording:  
Press the REC (s) button again.  
Recording will resume at the point of interruption.  
hLCD Display Information  
You can select an option for the display of the recorder. This will help review and confirm different  
recorder settings and file information.  
State of the  
recorder  
Operation  
Display  
While in stop  
mode  
Press and hold the  
STOP (4) button  
Whileholdingthebuttondown,“Remainingrecording  
time” and “Remaining memory” are displayed.  
While in record  
mode  
Press the DISP/  
MENU button  
Each press switches the display in the order  
of “Recording elapsed time”, “Remaining  
recording time” and “Recording level meter”.  
While in stop  
mode or  
playback mode  
Press the DISP/  
MENU button  
Each press switches the display in the order of  
Playback elapsed time”, “Remaining playback  
time”, “Date of recording” and “Time at  
recording”.  
 
4
- -  
Playback  
hPlayback  
1 Press the FOLDER/INDEX button to select  
the desired folder.  
2 Press the 9or 0button to select the file  
to playback.  
3 Press the PLAY/OK (`)  
button to start playback.  
The record/play indicator light  
turns green, and the elapsed  
playing time is indicated on  
the display.  
15m15s  
14m25s  
a Current file number  
b Playing time  
a
b
4 Press the + or – button to select the proper  
sound volume.  
The display shows the volume level. You can choose  
between [00] to [30].  
hCanceling Playback  
To Stop:  
Press the STOP (4) button.  
The recorder stops in the middle of the file being played.  
To Resume Playback:  
Press the PLAY  
/OK (`) button again.  
Playback will resume at the point of interruption.  
hForwarding and Rewinding  
Fast Forward:  
While the recorder is during playback mode, press and  
hold the 9 button.  
When you release the 9 button, the recorder will resume  
normal playback.  
Rewind:  
While the recorder is during playback mode, press and hold the 0 button.  
When you release the 0 button, the recorder will resume normal playback.  
Notes:  
The recorder pauses when it reaches to the end of the file during fast forwarding or fast rewinding.  
Pressing and holding it continues fast-forwarding or fast-rewinding.  
If there is an index mark or temp mark in the middle of the file, the recorder will stop at that  
location.  
hLocating the Beginning of the File  
While the recorder is during playback mode (playback  
or playback in slow/fast mode), press the 9 or 0  
button.  
Jumps to the beginning of the next file or the file being  
played back.  
Note:  
If there is an index mark or temp mark in the middle of the file, the recorder will stop at that  
location.  
 
5
- -  
hChanging the Playback Speed  
While the recorder is during playback mode, press the  
PLAY OK (`) button to change the playback speed.  
/
Slow Playback  
(-25%)  
Fast Playback  
(+50%)  
Normal speed  
Notes:  
When the slow playback mode is selected, the [J] appears and, for the fast playback mode, [K]  
appears on the display.  
Even if playback is stopped, the changed playback speed will be retained.  
The next playback will be at that speed.  
hHow to begin segment repeat playback  
1 While the recorder is  
during playback mode,  
press the REC (s) but-  
ton at the point you  
want to start segment  
repeat playback.  
Repeat End ?  
[Repeat End?] flashes on the  
display.  
2 Press the REC (s) but-  
ton again at the position  
where you want to end  
segment repeat play-  
back.  
15m15s  
02m15s  
The recorder repeatedly plays  
back the segment until the  
segment repeat playback is  
cancelled.  
Cancel the Segment Repeat Playback Function:  
1 Press the REC (s) button.  
2 Press the STOP (4) button.  
3 Press the 9 button.  
4 Press the 0 button.  
Erase  
You can easily erase unnecessary files. Sequential file numbers are reassigned automatically.  
hErasing One File at a Time  
1 Press the FOLDER  
/
INDEX button to select  
folder.  
a
2 Press the 9 or 0  
button to select the file  
to be erased.  
aFile to be erased  
3 Press the ERASE (s )  
button.  
4 Press the 9 button to select [Start].  
5 Press the PLAY/OK (`) button.  
Erase:  
Start  
File Erase!  
 
6
- -  
hErase All Files from a Folder  
a
1 Press the FOLDER  
/
INDEX button to select  
the folder to be erased.  
aFolder to be erased  
2 Press the ERASE (s )  
button twice.  
Erase:  
Cancel  
3 Press the 9 button to select [Start].  
4 Press the PLAY OK (`) button.  
/
All Erase!  
Erase Done  
Notes:  
An erased file cannot be restored.  
The file set to erase lock will not be erased.  
If operation is not executed for 8 seconds during the setting, it will return to the stop status.  
Completion of erasing may take several seconds. Do not attempt to remove, replace battery  
or attempt any other functions on the voice recorder during this period because data may be  
corrupted.  
Menu mode  
hThe levels of the menu screen and the operation  
buttons [Main Menu/Sub Menu]  
The setting can be switched by putting the recorder in menu mode.  
Press and hold the button for  
1 second or longer to put the  
recorder in menu mode.  
Go to the setting screen from the  
main menu or sub menu screen.  
Confirm the item selected in the  
setting screen, and go back to the  
main menu or sub menu screen.  
DISP  
/
MENU  
PLAY/OK(`)  
Switch the items of the setting  
screen in the main menu or sub  
menu screen.  
Complete the menu mode setting.  
(If pressed while the setting screen  
is displayed, the item being selected  
will not be set.)  
STOP (4) or  
0 or 9  
REC (s)  
 
7
- -  
hBasic Operation of the Menu Mode  
1 Whiletherecorderisdur-  
ing stop mode, press and  
hold the DISP/MENU  
button for 1 second or  
longer.  
Menu  
Guide icon: Tells you the next  
button to use by flashing.  
2 Press the 9 or 0  
button to select the  
menu item.  
Go to the setting screen of the  
selected menu item.  
To set the sub menu, select  
the [Sub Menu] from the main  
menu screen. And select and  
set the menu item from the  
sub menu screen in the same  
manner.  
Rec Mode  
a
b
a [ ]: Press the PLAY/OK(`) button (Goes to the next screen).  
^
\
b [ ] or [ ]: Press the 9 or 0 button (Changes the item).  
]
3 Press the PLAY/OK (  
`
)
button.  
4 Press the 9 or 0  
button to select the set-  
ting.  
To go to the main menu screen  
after the sub menu setting,  
select [Main Menu] from the  
sub menu screen.  
Mode:  
HQ  
5 Press the PLAY  
/OK (`) button to confirm the  
setting.  
6 Press the STOP (  
4
)
button to close the menu.  
Note:  
The recorder will stop if you leave it idle for 3 minutes during a menu setup operation, when a  
selected item is not applied.  
hRecording Modes [Rec Mode  
]
The recording mode can be chosen from [HQ] (high quality sound recording), [SP] (standard  
recording), [LP] (long-term recording), and [MP3] (MPEG1 layer 3).  
Current recording mode  
In Menu mode selection:  
Mode: HQ  
Mode: SP  
Mode: LP Mode: MP3  
Approx.  
141 h. 55 min.  
Approx.  
279 h. 20 min.  
Approx.  
888 h. 50 min.  
Approx.  
72 h. 35 min.  
05m35s  
00m00s  
Notes:  
The recording time shown above is for one continuous file. The available recording time may be  
shorter than specified if several files are recorded (Use the remaining time and recorded time  
only as references).  
The above-noted recording times indicate times after deletion of the manual data stored in the recorder.  
Microphone  
sensitivity indicator  
hMicrophone Sensitivity [Mic Sense  
]
Microphone sensitivity is adjustable to meet your recording needs.  
In Menu mode selection:  
Sense: Conf. (  
)
Sense: Dict. (  
)
g
i
05m35s  
00m00s  
Note:  
To ensure successful recording, make a test recording to select  
appropriate microphone sensitivity before recording.  
hUsing the Variable Control Voice Actuator [VCVA  
]
VCVA indicator  
When the microphone senses that sound has reached a preset volume,  
the built-in Variable Control Voice Actuator (VCVA) starts recording  
automatically, and stops it when the volume drops.  
In Menu mode selection:  
VCVA: Off  
VCVA: On  
05m35s  
00m00s  
 
8
- -  
Adjust the Start/Stop Actuation Level:  
a
1 While the recorder is during recording mode,  
press the 9or 0buttons to adjust the pause  
sound level.  
The VCVA level can be set to any of 15 different values.  
a VCVA Level  
05m35s  
00m00s  
b Start level (moves to the right/left according to the set level)  
Note:  
The record/play indicator light is lit during recording. When the  
recorder is in Standby mode, the Record/Play indicator light flashes  
and [VCVA] flashes on the display.  
b
LowCut Filter indicator  
h
Set the LowCut Filter [LowCut]  
The recorder has a LowCut Filter function to minimize low-frequency  
sounds and record voices more clearly. This function can reduce noise  
from air conditioners, projectors and other similar noises.  
In Menu mode selection:  
LowCut: Off  
LowCut: On  
05m35s  
00m00s  
hSet the Voice Filter [Voice]  
The recorder has a Voice Filter Function to cut low and high frequency  
tones during normal, fast, or slow playback, and enable clear audio  
playback.  
In Menu mode selection:  
Voice: Off  
Voice: On  
Voice:  
On  
Erase lock indicator  
hLocking Files [Lock  
]
Locking a file keeps important data from being accidentally erased.  
Locked files are not erased when you choose to erase all files from  
a folder.  
In Menu mode selection:  
Lock: Off  
Lock: On  
05m35s  
00m00s  
hSystem Sounds [Beep  
]
Informs a button operation or a wrong operation of the recorder by  
sound. System sounds may be turned off.  
In Menu mode selection:  
Beep: Off  
Beep: On  
Beep:  
On  
hLED [LED  
]
You can set it so the Record/Play indicator light does not turn on.  
In Menu mode selection:  
LED: Off  
LED: On  
LED:  
On  
hLCD Contrast Adjustment [Contrast  
Display contrast can be adjusted in 12 levels.  
In Menu mode selection:  
]
You can adjust the LCD display  
contrast level from [01] to [12].  
Contrast:Level06  
h
Set the Display Language [Language]  
You can select the display language for this recorder.  
In Menu mode selection:  
Lang.: English Lang.: Français Idioma: español  
Sprache: Deutsch Lingua: Italiano  
Lang. : English  
 
9
- -  
hFormatting the Recorder [Format  
]
If you format the recorder, all files will be removed and all function settings will return to defaults except  
date and time settings. Transfer any important files to a computer before formatting the recorder.  
1 The Sub Menu opens.  
2 Press the 9 or 0 to  
select [Format].  
3 Press the PLAY/OK (`)  
Format: Cancel  
button.  
[
] and [Cancel] flashes  
^ ]  
alternately.  
4 Press the 9 button to  
select [Start].  
5 Press the PLAY/OK (`)  
button.  
After the [Data All Cleared]  
message is on for 2 seconds,  
[Sure? Cancel] will turn on.  
Sure?:  
Cancel  
6 Press the 9 button again to select [Start].  
7 Press the PLAY OK (`) button.  
/
Formatting begins and [Format Done] displays when  
formatting ends.  
Format!  
Format Done  
Notes:  
It may take up to a minute to finish the initialization. Do not remove the battery or detach the  
battery compartment from the recorder during that time. Otherwise data may be damaged.  
Never format the recorder from a PC.  
When the recorder is formatted, all the stored data, including locked files, are erased.  
Recorder’s Version  
hViewing System Information  
[
System]  
You can check the recorder's information on the menu screen.  
Version : 1.00  
Other Functions  
hIndex Marks (HQ, SP, LP only)  
If index marks are placed, you can quickly find a location you want to listen to in fast forward and  
fast rewind and when cuing a file  
Cannot place the index mark to the recorded file on the [MP3] mode.  
Setting an Index Mark:  
1 While the recorder is  
during recording (pause  
re cording) or play-  
back mode, press the  
FOLDER/INDEXbutton  
Index 06 Set  
to set an index mark.  
Clearing an Index Mark:  
1 Locate the index you  
want to clear.  
2 Press the 9 or 0  
button to select the  
Index 02  
index mark to delete.  
3 Press the ERASE (s )  
button.  
Index 02 Clear  
Notes:  
Index marks cannot be placed on the recorded file on the [MP3] mode or files created on devices  
other than Olympus IC recorders, but temp marks can be placed instead to temporarily remember  
desired locations.  
Temp marks are temporary markings, so if you move to another file, or connect the recorder to a  
computer, they will be automatically erased.  
Up to 16 index and temp marks can be set in a file.  
Index or temp marks cannot be set or erased in a locked file.  
 
10  
- -  
hConnecting to Your PC  
Apart from using this unit as a recorder, you can use it as an external memory for your computer,  
as a storage device.  
The audio files recorded by this recorder can be played back on your computer using Windows  
Media Player. You can also transfer the WMA files downloaded with Windows Media Player to  
your recorder and enjoy them (excluding files with copyright protection).  
1 Connect the recorder’s  
USB terminal to a PC USB  
port or USB hub.  
Once [Remote] is displayed, you  
can save or read the data.  
USB terminal  
2 Transfer the audio files to your computer.  
Connect the recorder to your computer and launch Explorer.  
The recorder will be recognized as a removable disk.  
Each of the five folders is named as DSS_FLDA, B, C, D and E. The  
audio files are saved in these folders.  
All the audio files recorded by this recorder will be in WMA or  
Remote  
MP3 format.  
i.e.: VN760001.WMA or VN760001.MP3  
If you are using Windows 2000, Windows Media Player must be  
installed on the PC.  
Sending the date  
3 Click [ ] on the task bar located at the lower-  
right corner of the screen. Click [Safely Remove  
Hardware].  
PC  
Receiving the data  
PC  
hUsing the recorder on your PC  
Operating System:  
Microsoft Windows 2000/XP/Vista/7 (Standard Installation)  
Windows  
Compatible PC’s:  
Windows PC’s equipped with more than one free USB port  
Operating System:  
Mac OS X 10.2.8 ~ 10.6 (Standard Installation)  
Macintosh  
Compatible PC’s:  
Apple Macintosh series equipped with more than one free USB port  
The support service will not cover if your PC has been updated from Windows 95 or 98 to Windows  
2000/XP/Vista/7. Any failure on a self-modified PC will not be covered under the operational warranty.  
Notes:  
NEVER disconnect the USB while the record/play indicator light is flashing in red. If you do so, the  
data may be destroyed.  
Refer to the user's manual for your PC regarding the USB port or USB hub on your PC.  
As the noise may cause adverse effects on electronics devices nearby the recorder, unplug the  
earphone when you connect the recorder to a PC.  
Do not use USB connecting cables other than the supplied cable.  
General Precautions  
Read this manual carefully to ensure that you know how to operate it safely and correctly. Keep  
this manual in an easily accessible location for future reference.  
The warning symbols indicate important safety related informa tion. To protect yourself and others  
from personal injury or damage to property, it is essential that you always read the warnings and  
information provided.  
Warning regarding data loss:  
Recorded content in memory may be destroyed or erased by operating mistakes, unit malfunction,  
or during repair work.  
For important recorded content, we recommend you to write it down somewhere or make a back-up  
by downloading to a PC.  
Any liability for passive damages or damage of any kind occurred due to data loss incurred by a defect  
of the product, repair performed by the third party other than Olympus or an Olympus authorized  
service station, or any other reasons is excluded from Olympus’s liability.  
For safe and correct Usage  
Use your earphones only after sufficiently reducing the volume of the earphones, otherwise hearing  
impairment and/or hearing disorders may occur.  
Do not use your earphone at a high volume for an extended period of time as hearing impairment  
and/or hearing disorders may occur.  
Be sure to stop the recorder before replacing the batteries. Unloading the batteries while the recorder  
is in use may corrupt the file.  
Do not leave the recorder in hot, humid locations such as inside a closed automobile under direct  
sunlight or on the beach in the summer.  
 
11  
- -  
Do not store the recorder in places exposed to excessive moisture or dust.  
Do not use organic solvents such as alcohol and lacquer thinner to clean the unit.  
Do not place the recorder on top of or near electric appliances such as TVs or refrigerators.  
Avoid recording or playing back near cellular phones or other wireless equipment, as they may cause  
interference and noise. If you experience noise, move to another place, or move the recorder further  
away from such equipment.  
Avoid sand or dirt. These can cause irreparable damage.  
Avoid strong vibrations or shocks.  
Do not disassemble, repair or modify the unit yourself.  
Do not operate the unit while operating a vehicle (such as a bicycle, motorcycle, or gocart).  
Keep the unit out of the reach of children.  
Battery  
VWarning  
Under no circumstances insert any other parts than the main unit into the battery compartment. This  
may result in battery leakage, overheating, fire or explosion.  
Battery should never be exposed to flame, heated, short-circuited or disassembled.  
Do not attempt to recharge alkaline, lithium or any other non-rechargeable battery.  
Never use any battery with a torn or cracked outer cover.  
Keep battery out of the reach of children.  
If you notice anything unusual when using this product such as abnormal noise, heat, smoke, or a burning odor:  
1 remove the battery immediately while being careful not to burn yourself, and;  
2 call your dealer or local Olympus representative for servicing.  
Troubleshooting  
Q1: Nothing happens when a button is pressed.  
A1: The HOLD switch may be set to [HOLD] position.  
The batteries may be depleted.  
The batteries may be inserted incorrectly.  
Q2: No sound or quiet sound is heard from the speaker while playing back.  
A2: The earphone plug may be plugged into the recorder.  
The volume may be set to the minimum level.  
Q3: Recording is not possible.  
A3: By pressing the STOP (4) button repeatedly while the recorder stops, check if  
the display shows:  
• The remaining recording time in the selected folder may have reached [00:00].  
• The number of files is 200.  
Check if the display shows [Memory Full] by pressing the REC (s) button.  
Q4: The playback speed is too fast (slow).  
A4: The recorder may be set to fast (slow) Playback.  
Specifications  
Recording medium:  
Earphone jack (monaural):  
ø 3.5 mm diameter, impedance 8 Ω  
Microphone jack (monaural):  
ø 3.5 mm diameter, impedance 2 kΩ  
Power supply:  
Built-in flash memory  
Overall frequency:  
HQ mode: 200 to 13,000 Hz  
SP mode: 200 to 7,000 Hz  
LP mode: 200 to 3,000 Hz  
MP3 mode: 200 to 13,000 Hz  
Recording time:  
Two AAA (LR03) batteries or Two Ni-MH  
rechargeable batteries  
Continuous battery:  
VN-7600PC: 2 GB  
Alkaline batteries: Approx. 37 h.  
Ni-MH rechargeable batteries: Approx.  
25 h.  
HQ mode: Approx. 141 h. 55 min.  
SP mode: Approx. 279 h. 20 min.  
LP mode: Approx. 888 h. 50 min.  
MP3 mode: Approx. 72 h. 35 min.  
Microphone:  
Dimensions:  
102 (L) mm x 37 (W) mm x 18.8 (T) mm  
(without protrusions)  
Weight:  
Electret Condenser Microphone (mon-  
aural)  
Speaker:  
Built-in ø 23 mm round dynamic speaker  
Maximum power:  
64.8 g (including battery)  
The above-noted recording times indicate times  
after deletion of the manual data stored in the  
recorder.  
The manual data can be deleted by connecting  
to a computer and deleting or by formatting the  
recorder. For details, please see “Formatting the  
Recorder [Format]”.  
250 mW  
Maximun headphone output:  
150 mV (according to EN 50332-2)  
Wide band characteristic headphone output  
:
75 mV (according to EN 50332-2)  
Before deleting the data, please make a backup file of the PDF data of the manual.  
Battery life is measured by Olympus. It varies greatly according to the type of batteries used and the  
conditions of use.  
Your recorded contents are for your personal use or pleasure only. It is prohibited to record copyrighted  
material without permission of the copyright holders according to copyright law.  
Specifications and design are subject to change without notice for improvement of performance.  
hAccessories (Optional):  
Ni-MH Rechargeable Battery Charger:  
BU-400 (Europe only)  
Noise-Cancellation microphone:ME52  
Electret condenser microphone: ME15  
Dual monaural earphone: E20  
Telephone pickup: TP7  
Ni-MH Rechargeable Battery: BR401  
Connecting cord (Earphone jack  
Microphone jack): KA333  
Neck Strap: ST26  
 
12  
- -  

Miele Clothes Dryer T 4839 Ci User Manual
Mr Coffee Coffeemaker NL4 White User Manual
NAD CD Player C521BEE User Manual
Nady Systems Microphone PCM 200 User Manual
Nady Systems Microphone UHF 10 User Manual
NEC Server HV8600 User Manual
Nintendo Handheld Game System MAA RVO S USZ C0 User Manual
Numark Industries DJ Equipment DJ 24 User Manual
Optoma Technology Projector EP753 User Manual
Oregon Scientific Marine Radio WMR80 User Manual